titles_durable

The Durable locker is designed to withstand daily use and abuse. It has a 2 mil thick powder coat baked enamel finish. The latch channels have nylon glides and latch hooks have rubber bumpers to reduce noise. All doors come with Recessed handles and multipoint latch with a 16 gauge continues piano type hinges riveted to both door and frame.

TIER OPENINGS

Durable SeriesRecessed Multi-Point LatchDoor Pull

One Tier: 

66” & 78” have a shelf for storage of books and small articles.
18” deep lockers or more come with a coat rod and coat hooks.

Two Tier:

Accommodates two people in the same space as a single tier locker.

Three Tier: 

Accommodates three times as many people as the one tier lockers in the same floor space.

2 Person Lockers:

This is a space saving model that has sufficient space for two people while occupying about the same space as a single tier locker.
Full book compartment doors. All models 18” deep or deeper include coat roads.

Box Lockers:

4, 5, 6 tier lockers are known for their compact dimensions.
It allows multiple users in the smallest amount of floor space possible.
They have a friction catch door pull that allows the use of built-in locks or padlocks.
Note: (1,2 & 3) Tier Box Lockers have 16 gauge bottoms (4,5 & 6) Tier Box Lockers have 24 gauge bottoms.

16 Person Locker:

It accommodates 16 users in only 69” floor space. It includes a 45” coat rod. It can use built-in locks or padlocks.

Wall Mount Locker:

Efficient storage unit where space is an issue. It has 4 private compartments with a coat rod for 16 coats.
It can also be set on counters or cabinets without the coat rod.
 
part1
1. ADA Compliance: Lockers are to meet the Americans with Disabilities Act, accessibility guidelines.
They shall have recessed handles and shall be a single tier or lower opening of a double tier locker.
Locker bottom shall be a minimum of 9” off the floor, or an extra shelf placed 9” off the floor.
Single tier lockers shall have a shelf 48” off the floor.
Doors assigned for handicapped use shall have an appropriate symbol sign.
1.1 Submittals: Submit under provisions of Section 01 33 00.
Shop Drawings shall show dimensioned plans, elevations, and sections.
1.2 Delivery, Storage and Handling: Store product in manufacturers unopened packaging until ready for installation
to protect the locker finish and adjacent surfaces from damage.
part2
2. Acceptable Manufacturer: WEC Manufacturing.
2.1 Material: Steel parts shall be mild cold rolled commercial quality steel, capable of taking a high-grade enamel finish.
2.2 Door Frames: Shall be 16 gauge formed in a channel shape.
Vertical members shall have an additional flange to provide a continuous door strike.
Cross frame members should also be 16 gauge channel-shaped, including intermediate cross frame members on double and triple tier lockers.
2.3 Doors: Shall be 16 gauge, with louvers for ventilation channel shaped on both the lock and hinge side, with angle formations across the top and bottom
2.4 Handles: Shall be one piece 20 gauge deep drawn stainless cup designed to accommodate locks.
2.5 Latching: On single, double, triple, and two-person lockers the lifting trigger will be 14 gauge steel, attached to the latching channel.
The trigger will have a padlock eye for use with 9/32” diameter padlock shackle.
2.6 Hinges: Shall be 16 gauge full-length continuous piano type riveted to both door and frame.
Hinge shall maximize security and enhance resistance to abuse and vandalism.
2.7 Ventilation: Louvered doors in manufactures standard louver pattern.
2.8 Body: Hole spacing in locker body construction: not exceeding 9”.
Steel specially formed for added strength and rigidity and to ensure tight joints at fastening points.
2.9 Interior Equipment: Single tier lockers 48” or higher shall have a shelf.
When under 18” deep, locker shall have 3 wall hooks and one ceiling hook.
Single tier lockers 18” deep or more shall have a coat rod instead of one ceiling hook.
Triple tier lockers shall have three wall hooks for 12” and 4 wall hooks for 15” and wider lockers.
2.10 Fabrication: Shall be on the unit principle, each locker with individual door and frame, individual top, bottom, back, and shelves,
with common intermediate divisions separating compartments.
2.11 Number Plates: Provide holes for attaching number plates.
Each locker shall have a polished aluminum number plate riveted to door face with black numerals 1/2” high.
2.12 Finish: All components shall have a 2 mil hybrid epoxy/polyester powder, electrostatically applied to ensure a uniform finished and baked to cure.
2.13 Accessories: available upon request.
2.14 Locks: available upon request.
part3
3. Installation: Lockers shall be installed in compliance with WEC’s installation instructions and
shall be level and plumb with flush surfaces and rigid attachment to anchoring surfaces.
3.1 Adjust and Clean: Adjust doors and latches to operate without binding.
Verify that latches are operating satisfactorily.
Adjust built-in locks to prevent binding of dial or key and ensure smooth operation prior to substantial completion.
3.2 Protection: Protect installed products until completion of the project.

WEC Manufacturing is your One-Stop quality manufacturer and distributor of metal lockers for all types of applications.

Your One-Stop Source for All Things Storage, Convenience, Selection, and Savings. Biggest Selection, Best Prices, Nicest People

wec dealer

Built-in standard superior quiet locker features